Schedule And Pricing

Were you searching for suggestions around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Installing a bath tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is likewise a moderately tough project. If the old tub is conveniently obtainable, the job can relocate rapidly; if you need to open a wall to get rid of the old tub and also position the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to move out the old tub and embeded in the brand-new one. Ensure you have certified yourself for the work and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to take into consideration employing one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This article will certainly help you set up a brand-new bathtub in your washroom if you have currently bought a brand-new bathtub and do not require to change the setup of your previous water supply pipes.
Your devices and material list should make up the following:

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Planning for the Installation

First of all, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its final position.

Removing Old Touches

If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the restricted accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.

Installing the Bath tub

Utilizing the two wood boards under its feet, put the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the tub until the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable faucet port to the ideal supply pipe by making a compression sign up with; then do the same for the various other tap.
Turn on the water supply and examine all joints and brand-new pipework for leaks as well as tighten them if needed. Fill the tub as well as also examine the overflow outlet as well as the regular outlet for leakages.
Finally, fix the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the tub should wait up until the bath tub has been utilized at the very least once as this will resolve it right into its last position.

Fitting New Touches

If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines are in place between the tap and the sink. Protect the faucet in position with the supplier provided backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap ports. The former type ought to be connected to the tap ends initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

Tiling Around the Bath tub

In the location where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, resulting in problems with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealant can crack rather very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant sticky and cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you like reading about How to Install a Bathtub Yourself? Leave a comment below. We would be pleased to listen to your responses about this article. We hope to see you back again before long. Don't hesitate to set aside a second to share this blog post if you liked it. We enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.

Or Book Technician Here